草莓视频污下载app

模具配件加工注意事項

模具配件加工注意事項，要知道!

1、型芯鑲針介紹2D、3D型面粗加工，非安裝非工作平面加工。鎢鋼模具配件半精加工前，側基準面的找正確保精度。

2、精加工前，工藝基準孔基準面找正，鑲塊余量檢查，檢驗復查加工精度。鎢鋼模具配件精加工型面2D、3D，側沖型面及孔位，東莞模具加工精加工工藝基準孔及高度基準，精加工導向面及導向孔。

3、加工重要難點處，工藝要特別強調，需要組合加工處，工藝表達清楚。鎢鋼模具配件工藝編制簡明、表達詳細，加工內容盡量數值化表達。鑲塊需單獨加工時，注意加工精度的工藝要求注明。

4、鎢鋼模具配件注意事項：組合加工后，需單獨加工的鑲塊零件，組合加工時工藝安裝單獨加工的基準要求。鎢鋼模具配件中彈簧是容易損壞的，所以要選擇疲勞壽命長的模具彈簧。

型芯鑲針介紹近幾年，我國鎢鋼模具配件行業以平均15%以上的速度快速增長，遠遠高于國家GDP平均增值。其中，鑄造模具約占各類模具總產值5%，每年增長速度高達25%。當前恰逢我國汽車、摩托車工業進入快速增長期，產量連續多年大幅度增長。尤其是與鑄造工業密切相關的轎車增長較快，增加了對復雜、鑄造模具的需求。